
Click here to refresh missing image
TOOLS PROVIDED:
-
Wrench: 2.5mm short arm hex key.
-
Steel.
Drill: 3.00x41x70mm HSS Jobber. *Note: Drill is provided as a means to clean out or straighten existing pin holes.*
-
Punch: 3/32" x 7/8" dowel pin. Hardened 4140 alloy steel; Rc 47. ¼" x 2" Aluminum handle. *
Note: This punch is not designed to be used on difficult to remove pins such as
those soldered in place.* Complete installation instructions are supplied. SCOPE
& RINGS ARE NOT PROVIDED!
$59.00 - FREE Domestic Shipping
FITMENT NOTES: This
mount will NOT work for an M38/M44/T53! See Model MN384453SSM for a M38/M44/T53.
The pin holes in the rear sight block are often located inconsistently as a
result of the original manufacturing process. The two holes are frequently not
parallel to each other and may be out of alignment or skewed. The mount can only
accommodate so much of this misalignment. You should measure the center distances from pin to pin on both sides and check those with the dimensions listed in the SPECIFICATIONS to ensure that the mount will fit properly. A 3mm drill is provided and can be used to clean out and straighten (to some degree) without enlarging the pins holes once the pins are removed. The pin holes for the rear sight block are generally .118"(3.0mm) in diameter and the supplied 3mm bolts have a nominal OD of .115"(2.92mm). This tight fit along with the use of an appropriate liquid thread locker for the screws and nuts, as well as proper tightening of the same should result in no movement of the Mount during normal firing recoil. Occasionally the rear sight block itself, as it sits on the barrel dovetail underneath, can be out of alignment with the bore axis. This condition, if extreme, can adversely effect how the Mount sits.
TOOLS REQUIRED:
-
Safety glasses
-
heavy gloves
-
solid work surface or vise
-
hammer
-
flat blade screw driver
-
7/32" (5.5mm) socket driver or wrench
-
hand drill
-
liquid thread locker
-
A MAPP (Methyl Acetylene Propadience Propane) gas torch
-
heavy duty punch may be required to remove existing pins from the rear sight block if they are soldered in place.
You can usually find these items at your local hardware or plumbers supply. The application of heat, if done properly, will not cause damage. Keep in mind that you only need to reach the melting point of the solder and that this same temperature was achieved during original construction without adverse effects. Procedure provided in supplied instructions.
NOTE:
As with ANY scope on ANY mount, should it receive an impact (dropped, hit, etc.) it should not be trusted to be accurate. Thus the SEE-THRU feature of our Mount. You can always still use the original iron or open sights if you feel the Mount has been compromised. Design subject to change without prior notice.
Caution!
Improper installation or use may result in damage to property, severe injury, or loss of life. If for any reason this product does not function properly, discontinue use immediately. Always practice proper SAFETY & ensure an UNLOADED condition before beginning installation.
|
Scope your Mosin while preserving its historic integrity.
Steel Picatinny Rail, Mounts Over Rear Sight Block
***PLEASE READ SPECIFICATIONS & FITMENT NOTES BEFORE PURCHASING***
There is no need for bent bolt handle with this Mount.
FEATURES: Allows for mounting of Scout Scope or other long eye relief optics on your military surplus Mosin Nagant model 91/30 without the need to drill & tap receiver or make any permanent modifications to the firearm. It is designed to fit over rear sight block in order to allow for continued use of the original fixed/iron sights up to 100 meters.
The Mount is rigid steel
construction with Black Oxide finish. 100% Lifetime Warranty!
SPECIFICATIONS: The Mount will accommodate a front to
back (horizontal) pin center distance of 1.39" (35.3mm) to 1.82"
(46.7mm) and allows for .039" (1mm) of up and down (vertical)
movement. The Mount is designed to fit over rear sight blocks
that measure between .750"(19.05mm) and .787"(20.00mm) wide. The
total weight including hardware is 5.5 oz. We have made every
reasonable effort to ensure that this product will fit the
majority of M9130's. However, due to the large number of these
firearms produced over many years around the world, it is
impossible for us to allow for all manufacturing variation.
Proper tightening of all hardware should result in no movement
of the mount during normal firing recoil. If for any reason our
Mount does not work with your specific 9130 it can be returned
(undamaged) for a full refund.
UNIT:
-
Mount: CNC laser cut perimeter, die punched holes and mounting slots, form tapped threads and die press formed. 3/32" (13 ga.) thick HR, P&O type CS-B A569 carbon steel; 40000 psi yield strength. Black Oxide plated.
-
Picatinny Rail: CNC machined to MIL-STD-1913. 8" long. HR ATSM A36 low carbon steel; 36000 psi yield strength. Black Oxide plated.
-
Screws: #10-32 x ¼" flat head socket cap screws. Alloy steel; Rc 38-45 hardness.
HARDWARE:
-
Bolts: M3x.5 X 30mm socket head cap screw. Grade 12.9 medium carbon Q&T alloy steel; Rc 38-44 hardness; 160000 psi yield strength, 177000 psi tensile strength; 1.67 ft lbs tightening torque.
-
Nuts: M3x.5 Hex Nut. Grade 2 low carbon steel; Rc 32 hardness; 60000 psi tensile strength. Black Oxide plated.
-
Lock Washers: 3mm cut spring lock washer. Steel. Black Oxide plated.
-
Flat Washers: 3mm plain flat washer. Steel. Black Oxide plated
|